Back to Help Center

Product Support

Cobra Racing Big Bore Shocks – Installation, Oil Filling & Bleeding Guide

Updated November 4, 2026 7 min read

Cobra Racing Aluminum Big Bore Shocks are designed for compatible Traxxas 1/10-scale 2WD and 4WD vehicles, including the Slash, Rustler, Stampede, and Bandit.

These shocks are beefier than the factory shocks, with larger aluminum bodies, adjustable spring preload, and rubber bladders. Installation is pretty straightforward, but there are a few things you'll want to pay attention to, especially when it comes to filling the shocks with oil and making sure everything clears properly.

A few things to know before getting started:

  • The shocks ship dry. You'll need to fill them with silicone RC shock oil before running them. This is normal for performance shocks and allows you to choose the oil weight that works best for your setup.
  • Front mounting spacers are required. We've included these with the shocks to provide proper clearance around the suspension hardware.
  • Rear spacers may also be needed. Depending on your vehicle and suspension setup, you may need additional spacing in the rear as well. These spacers are also included.

Step 1: Remove the Factory Shocks

  1. Place your vehicle on a stable work surface.
  2. Remove the wheels if you need more room to work.
  3. Remove the upper and lower mounting screws from the factory shocks.
  4. Take off the original shocks and keep any mounting hardware you'll be reusing.
  5. Give the shock towers, suspension arms, and mounting points a quick inspection while everything is apart.

Make sure you've identified the correct front and rear shocks before installing the new set.

Step 2: Fill the Shocks with Silicone Oil

These shocks arrive without oil, so you'll need to fill them before installation. The oil controls how quickly the suspension compresses and rebounds, which makes a big difference in how your vehicle handles.

Recommended oil: We recommend starting with 40WT silicone RC shock oil in the front and 60WT in the rear. This is a good starting point for many Traxxas 1/10-scale setups, but you can always experiment with different weights depending on your driving style and terrain.

Keep in mind that oil weight ratings can vary between manufacturers. For consistency, we recommend using the same brand of oil in all four shocks.

Here's how to fill them:

  1. Remove the spring and lower spring retainer if needed to make the shock easier to work with.
  2. Unscrew the upper shock cap and remove the rubber bladder.
  3. Fully extend the shock shaft.
  4. Hold the shock upright and slowly add silicone shock oil until it's nearly full.
  5. Slowly move the shock shaft up and down a few times, keeping the internal piston below the oil level.
  6. You'll notice small air bubbles coming to the surface. That's normal.
  7. Set the shock upright and give those bubbles a few minutes to work their way out.
  8. Check the oil level again and top it off if necessary.

Tip: Don't pump the shaft too quickly. Slow, steady movement helps release trapped air without introducing more bubbles.

Use silicone RC shock oil, not automotive motor oil.

Step 3: Bleed the Shocks and Install the Rubber Bladders

Once the shocks are filled, the next step is bleeding them. This simply means getting the remaining air out and making sure there's enough room inside the shock for the oil to move properly.

Our Big Bore shocks use rubber bladders underneath the upper caps. These help compensate for the oil displaced by the shock shaft during compression.

Here's how to bleed them:

  1. Make sure the air bubbles from the filling process have cleared.
  2. Fully extend the shock shaft and check the oil level. Top it off near the rim if needed.
  3. Check that the rubber bladder is clean and seated correctly.
  4. Slowly compress the shock shaft about halfway while keeping the shock upright. Some oil may overflow, which is normal.
  5. Carefully place the rubber bladder onto the shock body, allowing excess oil to escape.
  6. Install the upper shock cap while holding the shaft in position.
  7. Tighten the cap until snug. There's no need to overtighten it.
  8. Wipe away any excess oil.

Before putting the spring back on, test the shock.

Slowly push the shaft in and pull it back out. You should feel smooth, consistent resistance throughout the stroke.

A little shaft rebound is normal with rubber bladder shocks.

If the shaft becomes unusually difficult to compress or stops before reaching its normal travel, there may be too much oil inside. Open the cap, adjust the oil level, and bleed it again.

If the movement feels inconsistent or you notice air inside, repeat the filling and bleeding process.

The halfway-compressed position is a starting point for bleeding these types of shocks. You may need to adjust the position slightly to get the right oil volume and smooth movement.

Once everything feels good, reinstall the spring and repeat the process for the remaining shocks.

Step 4: Install the Shocks Using the Included Spacers

This is one of the more important parts of the installation.

Our Big Bore shocks are larger than the factory shocks, so you need to make sure the bodies and springs have enough room around the suspension hardware.

We've included mounting spacers for this exact reason.

Front Shocks – Use the Included Spacers

The front shocks require spacers for proper clearance. Without them, the larger shock bodies or springs may rub against nearby suspension components.

  1. Position the front shocks at the factory mounting locations.
  2. Install the included spacers between the shock mounting points and the mounting surfaces to move the shocks away from nearby hardware.
  3. Make sure there's enough clearance around the shock bodies and springs.
  4. Install the mounting screws and tighten them securely, while allowing the shocks to pivot freely.
  5. Check around the suspension arms, shock towers, and steering components for any contact.

Don't skip the front spacers. They're included with the kit and help prevent rubbing or binding as the suspension moves.

Rear Shocks – Check Your Clearance

The rear shocks may or may not need spacers, depending on the vehicle and suspension setup.

  1. Position the rear shocks at the factory mounting locations.
  2. Check for contact between the shock bodies, springs, suspension arms, and nearby hardware.
  3. If anything touches or rubs, use the included spacers to move the shocks away from those components.
  4. Make sure the shocks can pivot freely at their mounting points.

If everything clears properly without additional spacing, you're good to go.

Step 5: Check Suspension Travel

Before putting the wheels back on and heading out, check that everything moves freely.

  1. With the vehicle supported, slowly move each suspension arm up and down.
  2. Watch the shock bodies and springs to make sure they're not touching anything.
  3. Turn the steering fully left and right while checking front shock clearance.
  4. Make sure the shocks can pivot naturally at their mounting points.
  5. Check the suspension through its full range of travel, from extended to compressed.

If you notice rubbing or binding, adjust the mounting spacers until everything clears.

One thing worth checking: Just because the shocks clear everything while the vehicle is sitting still doesn't mean they'll clear during full compression. Make sure you check the suspension through its entire range of movement.

Step 6: Adjust Spring Preload

The threaded adjustment collars let you adjust spring preload and fine-tune your vehicle's ride height.

  • Tightening the collar adds preload and generally raises the ride height.
  • Loosening the collar reduces preload and allows more suspension sag.
  • Try to keep the left and right sides reasonably balanced when starting out.

Keep in mind that spring preload doesn't actually make the spring stiffer. It changes how much the spring is compressed at rest.

Start with a moderate setting, take the vehicle for a run, and make small adjustments based on how it handles.

Final Installation Checklist

Before your first run, give everything one last look:

  • All four shocks are filled with silicone RC shock oil.
  • The shocks have been properly bled and the rubber bladders are installed.
  • The shock shafts move smoothly without unusual resistance.
  • The included front mounting spacers are installed.
  • Rear spacers have been added if needed.
  • Nothing is rubbing against the shock bodies or springs.
  • All mounting screws are secure, and the shocks can pivot freely.
  • The suspension moves through its normal travel without binding.

If everything checks out, you're ready to go.

Basic Maintenance & Troubleshooting

These shocks don't require much maintenance, but it's worth checking them occasionally, especially after running in dirt, mud, or rough terrain.

Shock feels unusually stiff

There may be too much oil inside, or the shock may need to be bled again. Remove the spring and check the shaft movement before making adjustments.

Shock feels too soft or bouncy

Check the oil level and make sure there's no trapped air. If everything is filled correctly, you may want to experiment with a heavier shock oil.

Shock is rubbing against suspension hardware

Check the mounting spacers. These shocks are larger than stock, so proper clearance is important, especially up front.

Oil around the upper shock cap

Check that the rubber bladder is seated correctly and the cap is snug.

Oil around the shock shaft

Inspect the shaft for scratches or damage and check the lower seals for wear.

After running, wipe dirt from the exposed shock shafts and periodically check the mounting screws and oil seals.

That's really all there is to it. Once the shocks are properly filled, bled, and spaced, you're ready to put them to work.

If you run into any questions during installation, feel free to reach out to Cobra Racing Support. We're always happy to help.

Products in this article