How to Install a Spur Gear on Your Traxxas X-Maxx or XRT (And Avoid Stripping It)
Updated November 5, 2026 · 5 min read
Replacing the spur gear on your Traxxas X-Maxx or XRT is a fairly straightforward upgrade. But there's one thing you absolutely want to get right: gear mesh.
Even a hardened steel spur gear can wear out or suffer damage if it's installed incorrectly. Whether you're replacing a worn factory gear or upgrading to a Cobra Racing MOD 1.0 or MOD 1.5 spur gear, taking a few extra minutes during installation can save you a lot of trouble later.
Here's how to do it correctly.
Step 1: Remove the Factory Spur Gear
Before starting, turn off your truck, disconnect both batteries, and remove them.
- Remove the body to access the motor and gear cover.
- Locate the gear cover next to the motor and remove its two retaining screws.
- Remove the four motor mounting screws from underneath the chassis.
- Carefully lift the motor away from the spur gear. Disconnect the motor wires if necessary, taking care not to damage any wiring.
- Remove the spur gear assembly, following your model's service layout.
- If you're replacing only the spur gear, remove the screws holding it to the existing mounting assembly and separate the old gear.
Tip: Take a picture before disassembly. It makes reinstalling the gear, mounting hardware, and motor-positioning pins much easier.
Step 2: Inspect the Pinion and Drivetrain
Before installing your replacement gear, take a minute to inspect the surrounding components.
Look for:
- Worn, chipped, or damaged pinion teeth.
- Loose pinion set screws.
- Excessive play in the spur gear mounting assembly.
- Damaged bearings or mounting hardware.
- Dirt, debris, or metal shavings inside the gear compartment.
If the old spur gear stripped, clean out any remaining debris before installing the new one.
Important: MOD 1.0 and MOD 1.5 gears cannot be mixed. If you're installing a MOD 1.5 spur gear, you must also use a matching MOD 1.5 pinion.
Step 3: Install the New Spur Gear Assembly
Cobra Racing spur gears come as complete assemblies, so there's no need to transfer the original spur gear mounting components.
- Position the new Cobra Racing spur gear assembly in place of the factory assembly.
- Make sure the assembly is properly seated and aligned with the drivetrain.
- Reinstall and secure the appropriate retaining hardware.
- Check that the assembly rotates smoothly without wobbling or binding.
If you're changing the pinion gear, make sure it fits your motor shaft and is properly secured. The pinion set screw should engage the flat portion of the motor shaft when applicable.
Before continuing: Verify that your chosen spur and pinion combination fits your truck's motor mount. Certain aftermarket gearing combinations, particularly MOD 1.5 setups, may require adjustable motor mounting.
Step 4: Set the Gear Mesh Correctly
This is the most important part of the installation.
Gear mesh is the amount of clearance between the teeth of your spur and pinion gears.
- Too tight: Creates unnecessary friction, heat, noise, and premature gear wear.
- Too loose: Allows excessive movement between the teeth, increasing the risk of stripped or damaged gears.
Traxxas uses a motor-positioning pin system to help establish proper gear mesh with supported gearing combinations.
If your selected gear combination is listed in your model's official pin-position chart, use the recommended positions.
For custom combinations, gear mesh may need to be adjusted manually.
How to Set Gear Mesh Using Paper
Traxxas also describes the paper method in its X-Maxx and XRT owner's manuals.
- With the batteries disconnected, remove the factory positioning pins if you're setting the mesh manually.
- Loosen the motor mounting screws enough to allow the motor to move.
- Place a narrow strip of ordinary notebook paper between the spur and pinion gears.
- Gently slide the motor toward the spur gear, allowing the paper to sit between the teeth.
- Hold the motor in position and tighten the mounting screws securely.
- Rotate the gears by hand to feed the paper through and remove it.
The paper should come out with visible tooth impressions, but it shouldn't be torn or tightly jammed between the gears.
Once removed, check the gears by hand. They should rotate smoothly with a slight amount of clearance between the teeth.
Don't force the gears tightly together. A small amount of backlash is normal and necessary.
If the gears bind, feel excessively tight, or have too much play, readjust the mesh before running the truck.
Step 5: Reassemble and Test
Once the gear mesh is correct:
- Double-check that the motor mounting screws are secure.
- Confirm the pinion set screw is tight.
- Rotate the drivetrain by hand and listen for unusual grinding or clicking.
- Reinstall the gear cover, making sure nothing rubs against the gears.
- Reinstall your batteries and place the truck on a secure stand with its wheels off the ground.
- Run the motor briefly at very low throttle and listen for unusual noises.
If everything sounds normal, take the truck for a short, gentle test drive.
Avoid full-throttle launches immediately after changing the gearing. Check the motor and ESC temperatures, especially if you've changed your gear ratio.
Common Spur Gear Installation Mistakes
The new spur gear strips quickly.
Check the gear mesh, motor mounting screws, pinion condition, and alignment. A loose motor or incorrect mesh can damage a new gear surprisingly quickly.
The gears make a loud grinding noise.
Stop running the truck and inspect the installation. Check for improper gear mesh, damaged teeth, or contact with the gear cover.
The motor or ESC runs hotter than before.
Your new gearing may be placing additional load on the power system. Check for binding and make sure the gear ratio is appropriate for your setup.
The factory motor pins don't line up.
Your chosen gear combination may not be supported by the factory pin-position chart. Don't force the motor into position. Verify compatibility and use an appropriate mounting arrangement.
A Few Final Tips From Cobra Racing
A stronger gear is only part of a reliable drivetrain. Proper installation matters just as much.
Before every major bash session, it's worth checking that the motor is securely mounted, the pinion hasn't loosened, and the gear compartment is free of debris.
And remember, hardened steel gears aren't indestructible. Incorrect gear mesh or loose mounting hardware can still cause damage.
If you're considering a gearing upgrade, Cobra Racing offers three hardened steel spur gear options for compatible Traxxas X-Maxx and XRT setups:
- 46T MOD 1.0: For compatible MOD 1.0 gearing combinations.
- 50T MOD 1.0: Another MOD 1.0 option for different gearing ratios.
- 35T MOD 1.5: For heavy-duty setups using a matching MOD 1.5 pinion and compatible mounting arrangement.
Not sure which one to choose? Read our MOD 1.0 vs. MOD 1.5 Gear Comparison Guide to learn the differences before upgrading.
The bottom line: Take your time setting the gear mesh. A properly installed spur gear will generally last much longer than one installed too tightly, too loosely, or with an improperly secured motor.