NOW OFFERING FREE U.S. SHIPPING
Fits Traxxas 4×4 Ultimate Slash BLUE Aluminum Front or Rear differential 4WD
$23.95
45
Items sold in last 11 days
In stock
Description
COBRA RACING BLUE Aluminum differential. This differential can be uséd for either the front or back, as they are exactly the same. So if you need to replace both differentials on your car, make sure to add 2 in the QTY dropdown. The differential housing is made of aluminum to enhance aesthetics and durability. All too often, when doing serious bashing or racing, sometimes the gears inside of the differential strip the entire housing, leaving your car dead in it’s track. These aluminum differnetials solve this problem because it is much harder to strip aluminum than it is with stock plastic differential housing.
Compatible with:
Traxxas Slash 4×4 / VXL / Platinum / Ultimate
Traxxas Rustler 4×4 / VXL
Traxxas Stampede 4×4 / VXL
Traxxas Hoss 4×4 / VXL
…and most other 1/10 4×4 traxxas RC cars (check manufacturer schematics).
What’s included in the package:
1 Blue aluminum differentials
A set of rubber sealed bearings
⚠️ Please Note: Not compatible with aluminum differential housings without “some” modification. Perfect / direct fit to stock or other plastic differential housing. The differential is pre-filled with grease, but for optimal performance and long-term durability, we recommend opening them up and either topping off the grease or replacing it with your preferred differential oil.
Break-In Period (Highly Recommended):
Once fully installed, it is highly recommended to perform a low-power break-in period. Run the vehicle at half power or on 2S for one to two full battery cycles before stepping up to 3S power. This helps ensure proper seating of internal components and extends the life of the differential.
Important Installation Note:
Depending on your specific setup, proper shimming may be required for correct differential operation. Failing to shim the differential correctly—when needed—can result in excessive wear and potential output gear failure. Always check fitment and adjust as necessary before running.
Additional information
| Weight | 3 oz |
|---|---|
| Dimensions | 7 × 1 × 4 in |
| Brand | Cobra Racing |
| Vehicle Brand | For Traxxas |
| Type | Motor |
| Color | Blue |
| Compatible Vehicle Type | Buggy, Monster Truck, Roller, Scale, Short Course Truck, Truck, Truggy/Stadium Truck |
| Compatible Models | Traxxas SLASH |
| Compatible Fuel Type | Electric, Nitro & Glow Fuel |
| MPN | N/A |
| Age Level | 12-16 Years, 17 Years & Up |
| Compatible Scale | 1:10 |
| Condition | New |
Reviews (4)
4 reviews for Fits Traxxas 4×4 Ultimate Slash BLUE Aluminum Front or Rear differential 4WD
100%
0%
0%
0%
0%
Only logged in customers who have purchased this product may leave a review.
Q & A (1)
Q & A
Ask a question
Fits Traxxas 4x4 Ultimate Slash BLUE Aluminum Front or Rear differential 4WD
Your question
* Question is required
Name
* Name is required
Email
* Email is required
Can you put these aluminum differentials in the Cobra racing differential housings? Wasn't sure if they were compatible together I just purchased your housings and wanted to make sure
Hey Shawn -
You can put the aluminum differential in our aluminum housing, however, you have to do a quick mod for it to work. The aluminum differentials are beefier then stock differentials. Usually, this isn't a problem because stock differential housing are slightly bigger (has more room), so they will fit in nicely, whereas, the aluminum housings are a direct fit (no extra room) for the stock differentials. So basically, if you try to put aluminum diffs in aluminum housing, you are going to get some binding.
Luckily, there is a quick (2 minute) fix for this. What you will need to do is swap out the outer differential ring from your stock differential, and put it on the aluminum diffs. The stock diff ring has a slightly smaller diamter then the aluminums. So if you do this, the aluminum differential will work flawlessly, with no binding.
Hope this helps.
(0)
(0)
Add an answer
Your answer
* Answer is required
Name
* Name is required
Email
* Email is required
Add to WishlistRemove from Wishlist
Add to Wishlist
Verified owner Anonymous (verified owner) –
Very satisfied
Verified owner Anonymous (verified owner) –
Worked great.
Verified owner Jared Grapentine (verified owner) –
The build quality was excellent, but the differential did not fit in my Traxxas/4 x 4 the ring gear would not make contact with the pinion gear inside the differential housing. I’m not sure if I put it in incorrectly or if there’s something I’m missing. I would like you to let me know. I put my old differential in and it is fine, also the body of the cobra differential is slightly longer than the body of the Traxxas/4 x 4 stock differential.
Store manager cobraracingtech (store manager) –
Hello, Jared –
Thanks for the feedback. These differentials are meant for the plastic / taxxas OEM housings. If you are installing these on any aluminum housings, they will not fit without modification. I am not sure if that is the case here, but assuming it is as these differentials are a direct fit to the plastic / traxxas OEM housings.
They reason why they won’t fit on the aluminum is, as you have stated, they have a slightly larger diameter then stock differentials (they are beefier). And aluminum housings are made to be an exact fit to stock differentials. So these will bind in aluminum, unless slightly modified.
FYI – we do have a note on the product page that these are not compatible on the aluminum housings without modifications. If it’s something else, send us an email with some photos, and we will be more then happy to assist you (we’re pretty sure it’s it’s most likely an installation issue).
Best,
CR Support
Verified owner Craig Trudell (verified owner) –
Like product so far